Luz Halogena Paglight D-Tap (500mm) & PowerMax w/dimmer

• Tungsten halogen news interview light


• Soft, even spectral distribution


• Fully focusable from spot to flood


• Cool-running design


• Rugged yet lightweight impact resistant construction


• Includes the PowerMax voltage regulated halogen lamp holder with dimmer


• 20W, 35W, 50W, 75W or 100W lamps sold separately


• This is a recommended model for cameras powered by Ni-MH or Ni-Cd Gold Mount batteries


• Patented interchangeable lamp unit design also accepts LED and HMI arc lamp units - one light does it all


• Hot-shoe Power Base with a D-Tap connector (lead length 500mm) for use with the light output on a battery mount


• Includes 1/4” Stud Adaptor and Camera Shoe Plate


• A Rotatable Accessory Kit that has a filter to convert halogen to daylight colour temperature is sold separately


• Reflector 45mm dia.


• 70mm wide x 103mm long x 115mm high

Paglight is the ultimate TV News camera top-light.

Paglight has a revolutionary patented design which allows a range of professional lighting technologies to be used with one lamp head. Interchangeable tungsten halogen, LED or HMI arc lighting modules, plug into the back of the reflector housing. They can be hot-swapped quickly and safely, in a matter of seconds. Paglight is the only broadcast light with this feature, providing you with the correct lighting technology for any professional situation.

This model incorporates a regulated 12V PowerMax halogen lamp holder for use with Ni-MH and Ni-Cd batteries. The voltage regulation feature extends battery run-time and prolongs lamp life. PowerMax incorporates a dimming facility for greater output control. 20W, 35W, 50W, 75W or 100W long-life halogen lamps are available for use with this model.

Paglight has an output that is soft and even. The lamp head incorporates a spot to flood feature for additional control, a feature not commonly found in camera top-lights.

The light is designed to be cool-running at all times and easy to handle.

The lamp body has a multi-directional mounting and may be adjusted vertically and horizontally. The desired position can be maintained by a locking lever situated on the side of the light base.

Paglight is supplied with a detachable hot-shoe Power Base that enables you to quickly attach the light to the camera, and remove it after shooting, leaving the power connection in place. This model incorporates a Power Base that has a cable length of 500mm, terminated with a D-Tap connector, suitable for the output on a battery mount fitted to the rear of the camera.

Paglight can be mounted to the camera using the 1/4” stud adaptor or the camera shoe plate supplied with the light.

DESCARGA CATALOGO EN PDF - PÌNCHA AQUI

ESPECIFICACIONES

Paglight:

Voltage: Nominal 12V to 14.8V battery supply.

Maximum Power Rating: 100W lamp with 13.2V battery.

Spot and Flood Angles: 
Flood 62°.
Spot 22.6°.

Dimensions:
Height: 115mm (4.5”).
Width: 70mm (2.7”).
Depth: 103mm (4”).
Without accessory kit, plug-in lamp unit or power base.

Weight: 233g (8.2oz) without accessory kit, plug-in lamp unit or power base.

Reflector size: 45mm (1.8”) dia.

PowerMax/VariLux Halogen Lamp Holder:

Input Voltage: Maximum 20V DC.

Output Voltage: Regulated 12V DC.

Maximum Consumption: 100W nominal.

Lamps: Low-voltage bi-pin, long-life halogen capsules (2000 hours at 12V approx.).

Voltage: Nominal 12V.

Watts: 20W, 35W, 50W, 75W or 100W.

Colour Temperature: 3200°K at 12V (5600°K with dichroic filter).

Filament: Axial filament with centre 30mm from end of pins.

Dimensions:
Height: 55mm (2.2”).
Width: 50mm (2”).
Depth: 119mm (4.7”).
With lamp protector.

Weight: 106g (3.7oz) with lamp and lamp protector.

Power Base:

Connector: 2-pin D-Tap type.

Lead Length: 500mm (19.7”).